You are here: Home > KTM
Sort By:
Page of 2
NGK Iridium CR8EIX
Our Price: $11.00
NGK Iridium DCPR8EIX
Our Price: $13.00
Float Height Gauge
Our Price: $16.00
FOR THE 950 ONLY the 990 uses a different plug!

Iridium IX® The Spark Plug Serious Enthusiasts Rely On Designed specifically for the performance enthusiast. Iridium IX® offers extreme ignitability, improved throttle response and superior anti fouling
  • Fine Iridium tip ensures high durability and a consistently stable spark
  • Iridium alloy has extremely high melting point, perfect for today’s high-tech, high-performance engines
  • Trivalent Metal Plating - superior anti-corrosion and anti-seizing properties
  • Outstanding acceleration, high fuel efficiency and durability
  • Ultimate design, technology and performance.
FOR THE EARLY 990 ONLY the later model 990 and 950 uses a different plug!

Iridium IX® The Spark Plug Serious Enthusiasts Rely On Designed specifically for the performance enthusiast. Iridium IX® offers extreme ignitability, improved throttle response and superior anti fouling
  • Fine Iridium tip ensures high durability and a consistently stable spark
  • Iridium alloy has extremely high melting point, perfect for today’s high-tech, high-performance engines
  • Trivalent Metal Plating - superior anti-corrosion and anti-seizing properties
  • Outstanding acceleration, high fuel efficiency and durability
  • Ultimate design, technology and performance.
Custom precision laser cut aluminum gauges for measuring and setting the float heights on the CV carbs fitted to the KTM 950.  Accurately measure 2.5mm, 3.0mm, 3.5mm, 4.0mm
KTM 950 Float Needle
Our Price: $18.59
Cable Guide, Scotts
Our Price: $22.95
Genuine OEM KEIHIN needle valve, with clip.  Fits KTM 950 all years and models.  Requires 2 (one for each carb)
Made in Japan
Set of two ADVmachines™ plates to block off the SAS ports on the side of the 690/950/990/1190/RC8 engine for testing. Precision CNC Laser cut from .187 6061 aluminum. CSE Scotts Submount Cable Guide
The submount Cable Guide is a must-have for KTM’s and Husaberg’s using Scotts submount, steering stabilizer systems.  The guide keeps the cables and hoses away from the stabilizer, handlebar clamp and handlebars preventing wear and cable snags that could eventually lead to an expensive, inconvenient or dangerous failure.
The Submount Cable Guides are machined from a wear resistant, tough copolymer plastic.  All mounting hardware is stainless steel to prevent corrosion.  Installation time is less than five minutes.



The Cable Guide was designed, built and tested by off-road riders and racers just like you.  Please contact us if you have any questions or comments.
LC8 Oil Filter
Our Price: $22.98
Double Take Mirror
List Price: $25.00
Our Price: $25.00
Facet pump adapter plate
Our Price: $25.50
Factory OEM paper filter, High quality stuff.  Will fit all 950 and 990 Adventure, 950 Super Enduro, 950 Supermoto, 990 Super Duke, RC8 Mirrors for the discerning road to dirt freaks and everyone else too!  These mirrors WORK!  No more loose floppy joints, or tools to adjust and tighten.  You can even SEE through this mirror when you are riding unlike some of the other light weight solutions that are only intended to cover your legal requirement to have a mirror.

Choose your arm and mount options based upon your application, check the Technical Description for more details.  If you are looking to mount it to a KTM 950/990 then go for either the Long or Short arm and the Ball Stud.Indestructible- Made from reinforced Zytel

Excellent visibility- SAE spec convex lens
This CNC milled 6061 aluminum adapter plate allows the installer to directly bolt in a Facet 40171 fuel pump in place of the OEM Mitsubishi pump on the SuperEnduro and SuperMoto tank without modifying the flanges on the Facet pump.  Requires 2 (two) 6mm x 10mm bolts, Facet pump, fuel filter, electrical connectors, pipe and/or tubing fittings to complete the conversion. The picture shown is a example of a finished installation.
KTM Tall drop-in SS Oil Filter
Our Price: $29.96
Sale Price: $26.78
You save $3.18!
KTM Short drop-in SS Oil Filter
Our Price: $29.96
Sale Price: $26.78
You save $3.18!
Enduro Fender Bag
Our Price: $27.99
KTM Stainless Steel, Reusable Oil Filter

KTM  Front, Tall Filter
400/450/520/525 EXC-F  00-07
400/450/520/525 XC-F   00-07
400/450/520/525 SX-F 00-06
540/620/625/640/LC4 (92-07)    690 all - 08


KTM 450/525 XC ATV          08-09

KTM  250 SX-F 05-09  250 XC-F/ XCF-W  07-09 (single filter engines)
Rear, Short Filter, KTM, Polaris, Husaberg

KTM    Rear, Short Filter
400/450/520/525 EXC-F      00-07
400/450/520/525 XC-F      00-07
400/450/520/525 SX-F      00-06
690 all (08)

KTM    450/525 XC ATV       08-09

Polaris Outlaw 450/525       07-09
Husaberg            all 4-Stoke Models      95-09
Enduro Fender Bag

By utilizing 1” webbing and heavy duty hooks, Ballistics nylon and Tough-Tek, Wolfman is offering a stable and durable bag to carry your spare tubes and tire irons. Tested on the grueling Colorado 500, this bag stays put.
WP Comp/Reb Knobs
Our Price: $28.95
These knobs replace the factory compression or rebound knobs on WP forks on the 690 as well as the new 1190 ADV-R. The CSE knobs are machined from aluminum to make them much more durable than the stock plastic knobs.  The shape of the knob has also been optimized to make adjustments easier.  They will also give your bike a custom look. The CSE Cable Guide is a must-have for KTM’s and Husaberg’s using standard, bar-mount steering stabilizer systems.  The guide keeps the cables and hoses away from the stabilizer, stabilizer adjustment knobs, handlebar clamp and handlebars preventing wear and cable snags that could lead to an expensive, inconvenient or dangerous failure.

The CSE Cable Guides are machined from billet 6061 Aluminum.  They can be purchased with a machined surface or anodized orange or black.  All mounting hardware is 18-8 stainless steel to prevent corrosion.  Installation time is less than five minutes using the included hex wrench.

The CSE Cable Guide was designed, built and tested by off-road riders and racers just like you.  Please contact us if you have any questions or comments.
The CSE Cable Guide is a must-have for KTM’s and Husaberg’s using standard, bar-mount steering stabilizer systems.  The guide keeps the cables and hoses away from the stabilizer, stabilizer adjustment knobs, handlebar clamp and handlebars preventing wear and cable snags that could lead to an expensive, inconvenient or dangerous failure.

The CSE Cable Guides are machined from billet 6061 Aluminum.  They can be purchased with a machined surface or anodized orange or black.  All mounting hardware is 18-8 stainless steel to prevent corrosion.  Installation time is less than five minutes using the included hex wrench.

The CSE Cable Guide was designed, built and tested by off-road riders and racers just like you.  Please contact us if you have any questions or comments.
CPR Rottweiler Prefilter
Our Price: $29.95
AFAM 525 CS Sprocket 16T
Our Price: $36.95
AFAM 525 CS Sprocket 17T
Our Price: $36.95
Dramatically increase filter service intervals with our pre filter skins. Available in standard 40 cell (red) or 60 cell (dark grey). The 40 is more 'coarse' foam where the 60 is more 'fine'.  Both will provide additional protection, the 60 will become 'plugged' sooner, however if running in fine silt/dust everyday we recommend the 60 provided it can be cleaned everyday.  Multiple pre oiled units can be swapped out in minutes without removing the base filter and are cleaned much easier as well. Afam's steel sprockets aren't just stock replacement products. Besides a broad range of alternative gear ratio's, the quality of Afam steel sprockets exceeds the OEM quality. All countershaft sprockets are made of superior quality case hardened alloy steel for extreme strenght and wear resistance. Fits all models of the KTM LC8, 950/990

16 Tooth count
Afam's steel sprockets aren't just stock replacement products. Besides a broad range of alternative gear ratio's, the quality of Afam steel sprockets exceeds the OEM quality. All countershaft sprockets are made of superior quality case hardened alloy steel for extreme strenght and wear resistance. Fits all models of the KTM LC8, 950/990

17 tooth count
ITG Prefilter
Our Price: $46.95
Dramitically increase filter service intervals with the ITG pre-filter. Available in a medium/coarse filter material.  Multiple pre oiled units can be swapped out in minutes without removing the base filter and are cleaned much easier as well.  Will fit the CPR or the ITG main filter.  The difference between this pre-filter and the CPR unit is this is thicker (more filter material) as well as this is 'medium' pour material. Afam's steel sprockets aren't just stock replacement products. Besides a broad range of alternative gear ratio's, the quality of Afam steel sprockets exceeds the OEM quality. All countershaft sprockets are made of superior quality case hardened alloy steel for extreme strenght and wear resistance. Fits all models of the KTM LC8, 950/990

42 tooth count
Afam's steel sprockets aren't just stock replacement products. Besides a broad range of alternative gear ratio's, the quality of Afam steel sprockets exceeds the OEM quality. All countershaft sprockets are made of superior quality case hardened alloy steel for extreme strenght and wear resistance. Fits all models of the KTM LC8, 950/990

45 tooth count
CPR Rottweiler "Snap Out"
Our Price: $59.95
Facet Fuel Pump
Our Price: $59.98
This compound is our 1375 compound on a diet. It has all the great features of the G1375 compound with the exception of the ceramic coated backing plate. Looking for that perfect brake pad to do those canyon runs? This is it! Very easy on the discs and great heat recovery. This compound is available for most applications. NEW!: Fits stock air-box AND 03-06 950's! 20 Second Rottweiler Filter removal! Have your glove box off in one snap. (Instead of 12 aggravating bolts) Works with stock air-box snorkel, Uni Pre-Filter or Rottweiler Intake System.  The '950' option is $10 more because there is a ECU relocation bracket included to move the ECU to clear the 'Snap Out'. Solid State fuel pump, replaces the KTM OEM unit that is prone to failures.
Water Pump shaft kit 950
Our Price: $81.00
Mounting plate for all LC8 KTM Slave Cylinders, this product replaces the OEM plastic version. The Billet aluminium version produced by Oberon Performance will improve the mounting of either the original Slave Cylinder or the Oberon replacement KTM Clutch Slave Cylinder. Additionally due to the natural heat dissipation of the alloy used in the plate, a cooler running condition will prevail allowing a better clutch operation and more reliable performance.
Note: You must retain the original spacers from your plastic backing plate and insert them into this mounting plate to complete the assembly.
Pump shaft and seal kit with 2 small circlips for shaft. SUPER DUKE AND SUPER MOTO!
Our 1375 compound is the result of many long days at the racetrack and on the brake dyno. Based on Advanced Ceramics, this compound is meant for the track. It offers very fast heat recovery for more consistent braking which, in turn, gives the rider more “feel”. This is the pad of choice for most aggressive street riders and racers at the top of club levels and AMA contenders. These pads are very easy on rotors since they do not have the same levels of metallics in them as many O.E.M. and after-market brands. The 1375 compound also features a ceramic-coated back plate, which helps to dissipate heat away from the brake pad and reduces the amount of heat transferred into the caliper pistons. This gives you a cooler running system that will be able to withstand more heating cycles and deliver consistent braking. Available for front calipers Supersport and Superbike applications (600cc – 1000cc)
Jetting Package
Our Price: $89.00
Sale Price: $84.00
You save $5.00!
Mduro KTM 690 Boot Guard
Our Price: $92.98
Sale Price: $88.98
You save $4.00!
Baseline kit to support a Prefilter on a OEM airbox.
Presently ON ORDER WITH Mduro, place order now to ensure that you get one of the next batch!

Mduro™ KTM 690 Boot guard kit is CNC milled and hard anodized aircraft grade aluminum alloy, its function goes beyond the technical! Design factors are similar to the Rear Brake master cylinder for the KTM 950/990.
Note: This item ONLY works with the Rottweiler Intake Filter Installed

The eagerly anticipated "Dog House" cargo box for the ADV! Fills in the hole created when you install the Rottweiler Intake System and the bottom of your seat pan becomes the sealed lid with a perfectly formed fit.

This is a 990 fit ONLY!

It _CAN_ be made to fit a 950, however requires modification of both the frame (removal of two unused tabs) and cutting the front of the dog box to fit the CV diaphragm housing of the rear carb. It has been done, but you need to know that cutting is required to fit the 950, buyer be aware!